【前言】
在SMT设备贴片之前,需要作业人员将料盘放在正确的Feeder上,再把Feeder放在合适的SMT设备的站位上,在实际操作过程中,经常发生用错物料或用错Feeder的情况,由于SMT设备是高速连续运行,如果不能事先避免这种错误,将造成返工或报废从而给企业带来巨大损失。
在SMT设备贴片之前,需要作业人员将料盘放在正确的Feeder上,再把Feeder放在合适的SMT设备的站位上,在实际操作过程中,经常发生用错物料或用错Feeder的情况,由于SMT设备是高速连续运行,如果不能事先避免这种错误,将造成返工或报废从而给企业带来巨大损失。
主要功能有:SMT上料系统功能介绍
备料 Prepare Picking
上料 Load Verify
换料 Change Material
换线 Stop Picking
对料 Check
上料 Load Verify
换料 Change Material
换线 Stop Picking
对料 Check
电话:13530890647
QQ:275300932
QQ:275300932
第一步
当外包装印有 Bar-code 时需将标签割下贴在 Reel 或 Tray 上。
CSP/BGA 等重要零件系统已经将 Lot 修正为必刷,请依规定扫描。
CSP/BGA 等重要零件系统已经将 Lot 修正为必刷,请依规定扫描。
When external package have barcode label must remove it and stick to reel/tray.
CSP/BGA critical component must scan “Lot”.
CSP/BGA critical component must scan “Lot”.
第二步
如果Feeder 不存在。
请随线工程师至 Server 端新增 Feeder。
请随线工程师至 Server 端新增 Feeder。
Feeder not exist.
Request line engineer help to add feeder to system.
Request line engineer help to add feeder to system.
第三步
料号不存在 BOM 中。
确认选择正确之工单。
确认料卷上之料号正确且为目前之机种所使用。
重新完成程序。
确认选择正确之工单。
确认料卷上之料号正确且为目前之机种所使用。
重新完成程序。
Feeder # 料架条形码 必刷
Parts # 料号必刷
Date Code 周期 必刷
Qty 数量 必刷
Supplier 供货商
Lot 批号
先刷 Feeder 再刷 Slot 完成后上架。
清单中的 Slot 会在每刷一笔数据后清除,当完全清空代表所有 Feeder 已架上 Slot。
当清单清空,以后使用”上料”功能,每ㄧ次都会启动控制箱解除,反之若清单中还有未上料数据,则该功能不会启动。
清单中的 Slot 会在每刷一笔数据后清除,当完全清空代表所有 Feeder 已架上 Slot。
当清单清空,以后使用”上料”功能,每ㄧ次都会启动控制箱解除,反之若清单中还有未上料数据,则该功能不会启动。
Scan feeder and slot finish load component.
When scan feeder and slot done, system will confirm and clean the un-verify slot.All scan procedure finish the list will empty.
When list empty, every time you scan “load verify” will start “unlock” function. If the list not empty the unlock function will not start.
When scan feeder and slot done, system will confirm and clean the un-verify slot.All scan procedure finish the list will empty.
When list empty, every time you scan “load verify” will start “unlock” function. If the list not empty the unlock function will not start.